Arizona Chapter
American Concrete Institute

Flatwork Finisher/Technician Certification Tucson

  • 06 Oct 2017
  • 7:00 AM - 11:00 AM
  • Cemex Plant 9121 N Casa Grande Highway, Tucson, AZ 85743
  • 10

Registration

(depends on selected options)

Base fee:
  • An individual member, or an employee of a corporate member of the Arizona Chapter of ACI (an employee must be registered by a company representative who has a log in for this site)
  • Exam Only, no review session or book included.

ACI Flatwork Finsiher/Technician Certification

This program includes a short classroom review, followed by the written exam. The package price includes the review, the exam, all certification fees and the ACI workbook (CP10) for this program. Note that this program does not include a performance exam. Applicants who pass the written exam will be issued a Flatwork Technician Certification unless they submit acceptable work experience forms which are a substitute for the performance exam and qualifies them for the Flatwork Finisher Certification. Please click here for work-experience forms & instructions.

Registger on-line here by clicking on the "Register" button at the bottom left side of this page.

A Concrete Flatwork Finisher is a craftsman who has demonstrated knowledge about and the ability to place, consolidate, finish, edge, joint, cure and protect concrete flatwork.

A Concrete Flatwork Technician is a person who is knowledgeable about proper procedures to place, consolidate, finish, edge, joint, cure and protect concrete flatwork, but who lacks sufficient work experience to qualify as a Concrete Flatwork Finisher.


Scope and Knowledge

The primary technical resource for this program is ACI's Concrete Craftsman Series, Slabs on Grade, CCS-1. The program requires knowledge in the following areas of concrete construction:

  • Planning for slab-on-ground placement
  • Concrete materials, mixture proportioning, and control tests
  • Preparation before placing concrete
  • Floor flatness and levelness
  • Placing equipment
  • Finishing tools and equipment
  • Procedures for finishing slabs-on-ground
  • Jointing
  • Curing and protection of concrete
  • Finishing problems and possible solutions


Certification Requirements

For Concrete Flatwork Finisher:

ACI will grant certification only to those applicants who obtain a passing grade on the written examination and either:

  • Possess one year (1500 hours) of approved work experience and successfully complete the ACI performance examination, OR
  • Possess three years (4500 hours) of approved work experience and successfully complete the Alternative Performance Affidavit (Form D16).

The work experience must include placing, consolidation, finishing, edging, jointing, curing, and protection of concrete flatwork. Verification of the amount and range of work experience by the applicant's employer(s) is required. Please click here for work-experience forms & instructions.

The two-hour written examination is "closed book" and consists of approximately fifty multiple-choice questions. The passing grade for the written examination is 70%.

During the performance examination each examinee must place, consolidate, finish, edge, joint, begin curing and provide initial protection for a concrete slab. The examiner will observe and evaluate the techniques used and record passing or failing grades on the various individual procedures. A passing grade is defined as "no significant variation from proper procedure and no more than two variations from proper technique in the use of the tools."

The Alternative Performance Affidavit (Form D16) is a possible alternative to the performance examination. It requires each applicant to submit a signed affidavit(s) from current and/or previous employers verifying that the applicant's proven abilities are equivalent to those listed in the ACI performance examination checklist.

Note: Optional forms and procedures are available for self-employed finishers.

Recertification is necessary every five years, and requires successful completion of a written examination.

For Concrete Flatwork Technician:

ACI will grant certification to those examinees who obtain a passing grade on the written examination. Individuals with Flatwork Technician certification can upgrade to full Flatwork Finisher status upon submittal and approval of sufficient work experience, and successful completion of the ACI performance evaluation.

Recertification is necessary every five years, and requires successful completion of a written examination.

  

Americans with Disabilities Act (ADA)

ACI Certification programs are ADA compliant.

Individuals with disabilities requiring special accommodations must contact the ACI Certification Department for further information on how to proceed. All requests for special accommodations under ADA are handled on a case-by-case basis and must be made allowing enough time for evaluation and appropriate action by ACI.

To contact the ACI Certification Department regarding ADA issues, call 248-848-3790

 

Powered by Wild Apricot Membership Software